VIDEO SUPERVISION RECEIVER - new
Item # Arr-e008
Price: B$95.00 B$85.00
Shipping (Free Shipping within Brunei / B$10.00 outside Brunei)
Beli Sekarang
/ Buy Now
SOLD
Solution of Frequently-met Problems in Use
1.The Indicatory Light Cannot Work
Please check up whether the power adaptor of the receiver inserts into the
interflow power plug correctly, wherther it contacts well or not, whether
the interflow power switch is on or not, and whether the DC output plug of
the power adaptor isinserted into the power input plug of the receiver.
2.The Picture Cannot be Received of the Received Picture is not Clear
Please check up :
A.Whether the camera transmitter has been put through the power of not ;
B.Whether the distance between the camera transmitter and the receiver is
too far or not (the distance of the open area is 50-100m), or whether
there are obstacles between the camera transmitter and the receiver or not
(for example : the building with iron-and-steel component part can cause
big obstruction to the sending signals);
C.Whether the frequency of the camera transmitter is corresponding to that
of the receiver of the reciver or not (there cannot be two camera
transmitters with the same frepuency working at the same time in the
effective distance, otherwise, they can interfere with each other to cause
the weak effect of the received picture) ;
D.Whether the receiving antenna of the receiver is installed to the
correct position or not and whether its direction is proper or not;
E.The antenna of the receiver is kept as far as possible from bigger
electromagnetic screened abjects, such as copper and iron ;
F.Signals with the big efficiency and the same frequency and working radio
station around on the car can cause interference to the receiver.
Accessories and datum
1.Antenna : one piece
2.AV line : one piece
3.Camera transmitter : one piece
4.DC + 12V/500mA power adaptor : one piece
5.DC + 8V/200mA power adapto : one piece
6.Manual : one piece
7.Warranty card : one piece
|
VIDEO SUPERVISION RECEIVER 
Arr-032
List Price: B$95.00
Our Price: $85.00
You Save: $10.00
Description:
Manual of RC 100A Wireless Supervision Receiver
Thank you for choosing RC 100A wireless supervision receiver.
Please read this manual carefully before you use it, and it will benefit
you to use this product better.
This product is suitable for the supervision of the places such as
supermarkets, department stores, homes, workshops, hospitals and so on.
Basic Specification Parameters
Tune mode : Voltage tune
Video output : 75 / 1Vp-p
Audio output : 10 K/200mVp-p
Power consumption : <2W
Work temperature : 0~40 C
Size : 115x60x20 MM
Validity Pixel : PAL/ NTSC
Horizonial Resolution : 380 Line
Lighting distance :100 m
Power Supply : camera : DC8V 200mA Receiv : DC6V 800 mA
Operating Instruction
1.Camera Transmitter
A.Install the camera transmitter foward thd direction you need to monitor.
B.Insert the DC+8V/200mA power adaptor into the interflow power plug, and
insert its DC output plug intjo the DC input plug of the camera
transmitter to put through the circuit.
2.Receiver
A.Insert the antenna into the antenna interface of the receiver and fasten
it.
B.Use AV line to connect the audio and video output interface of the
receiver with the audio and video input interface of the TV set or
monitor.
C.Insert the DC+12V/500mA power adaptor into the interflow power plug, and
insert its DC output plug into the DC input plug of the receiver to put
through the circuit, and at the moment the power indicatory light shines.
D.Adjust the frequency controller of the receiver to the sending frequency
of the corresponding camera transmitter with hands,and you can get the
picture and sound by the TV set. Adjust the supervision position of the
camera transmitter to the supervision object, and you can make effective
supervision.
3.The Matter Need Paying Attention to
The two kinds of power adaptjors of DC + 12V/500mA and DC+ 8V/200mA must
be not mix-used, in order to avoid to cause the circuit damage of the
camera transmitter.
|
